# Piezoelectric Atomization Physics

**C88 Knowledge Base — Chapter 01**  
**Last Updated:** 2026-11-18  
**Purpose:** Fundamental physics of ultrasonic atomization for C88 design and supplier evaluation

---

## 1. Ultrasonic Atomization Mechanism

### 1.1 Overview

Ultrasonic atomization converts liquid into fine droplets using high-frequency vibration (typically 1-3 MHz). When a piezoelectric ceramic disk vibrates at ultrasonic frequencies, it creates standing capillary waves on the liquid surface. As wave amplitude increases, droplets are ejected from wave crests.

**Key insight:** Droplet size is determined primarily by **frequency**, not power. Higher frequency = smaller droplets.

### 1.2 Two Competing Theories

**Theory 1: Capillary Wave Hypothesis (Lang, 1962)**
- Dominant theory, widely accepted
- Droplets form at peaks of capillary waves
- Wave wavelength determines droplet size
- Works well for MHz frequencies

**Theory 2: Cavitation Hypothesis (Sollner)**
- Bubbles form and collapse, creating shockwaves
- Shockwaves break liquid surface into droplets
- More relevant for low-frequency (<100 kHz) applications
- At MHz frequencies, cavitation requires too much power

**Combined Theory (Bograslavski & Eknadiosyants)**
- Both mechanisms work together
- Cavitation shockwaves enhance capillary wave breaking
- Controversial: some researchers argue cavitation is negligible at MHz

**C88 relevance:** At 1.7MHz, capillary wave mechanism dominates. Cavitation is minimal.

---

## 2. Lang's Equation — Frequency-Droplet Size Relationship

### 2.1 The Fundamental Formula

Lang (1962) derived the relationship between ultrasonic frequency and droplet size:

```
D = 0.34 × λ_c
```

Where:
- D = mean droplet diameter (m)
- λ_c = capillary wavelength (m)
- 0.34 = empirical constant (later adjusted by Yasuda)

### 2.2 Capillary Wavelength

The capillary wavelength is related to frequency by:

```
λ_c = (8πσ / ρf²)^(1/3)
```

Where:
- σ = surface tension of liquid (N/m)
- ρ = liquid density (kg/m³)
- f = ultrasonic frequency (Hz)

### 2.3 Combined Formula

Substituting λ_c into Lang's equation:

```
D = 0.34 × (8πσ / ρf²)^(1/3)
```

**Simplified for water (σ = 0.072 N/m, ρ = 1000 kg/m³):**

```
D ≈ 4.3 × f^(-2/3)    [D in µm, f in MHz]
```

### 2.4 Calculated Values for C88

| Frequency | Droplet Size (water) | Application |
|-----------|---------------------|-------------|
| 1.0 MHz | 4.3 µm | Large droplets, humidification |
| **1.7 MHz** | **2.3 µm** | **C88 primary** |
| 2.0 MHz | 1.9 µm | Medical nebulizers |
| **2.4 MHz** | **1.5 µm** | **C88 alternative** |
| 3.0 MHz | 1.2 µm | Sub-micron applications |
| 5.0 MHz | 0.8 µm | Nanoparticle synthesis |
| 8.5 MHz | 0.5 µm | Sub-micron, pharmaceutical |

**C88 calculation:**
- 1.7 MHz → D = 4.3 × (1.7)^(-2/3) = 4.3 × 0.54 = **2.3 µm** ✓
- 2.4 MHz → D = 4.3 × (2.4)^(-2/3) = 4.3 × 0.43 = **1.8 µm** (not 1.5µm as commonly stated)

**Note:** Actual droplet size distribution is broader than single value. Typical range: 0.5-5 µm for 1.7MHz.

---

## 3. Piezoelectric Effect

### 3.1 Basic Principle

Piezoelectric materials generate electric charge when mechanically stressed (direct effect) and deform when electric field is applied (converse effect).

**Converse piezoelectric effect (used in atomizers):**
```
Strain (S) = d₃₃ × Electric Field (E)
```

Where:
- S = mechanical strain (dimensionless)
- d₃₃ = piezoelectric charge coefficient (C/N or m/V)
- E = applied electric field (V/m)

### 3.2 PZT Materials (Lead Zirconate Titanate)

**Most common piezoelectric ceramic for atomizers:**

| PZT Type | d₃₃ (pC/N) | Curie Temp (°C) | Application |
|----------|------------|-----------------|-------------|
| PZT-4 | 285 | 328 | High-power, industrial |
| PZT-5A | 374 | 365 | General purpose |
| PZT-5H | 593 | 193 | High sensitivity |
| PZT-8 | 248 | 300 | High-power, low loss |

**C88 typical:** PZT-4 or PZT-8 (high power, stable at elevated temperature)

### 3.3 Resonance Frequency

A piezoelectric disk has multiple resonance modes:

**Radial mode (thickness expansion):**
```
f_r = v / (2 × d)
```

Where:
- f_r = radial resonance frequency (Hz)
- v = speed of sound in PZT (~4000 m/s)
- d = disk diameter (m)

**Thickness mode:**
```
f_t = v / (2 × t)
```

Where:
- f_t = thickness resonance frequency (Hz)
- t = disk thickness (m)

**Example calculation:**
- 20mm diameter, 1mm thick PZT disk
- Radial mode: f_r = 4000 / (2 × 0.02) = 100 kHz
- Thickness mode: f_t = 4000 / (2 × 0.001) = 2 MHz

**C88 operation:** 1.7 MHz is between radial and thickness modes. This is the **flexural mode** (bending vibration), which is most efficient for atomization.

---

## 4. Atomization Performance

### 4.1 Mist Production Rate

Mist output scales with:
- Disk diameter (larger = more output)
- Drive power (higher = more output)
- Liquid properties (lower viscosity = easier atomization)

**Empirical formula:**
```
Q = k × P × D²
```

Where:
- Q = mist production rate (g/h)
- P = drive power (W)
- D = disk diameter (mm)
- k = empirical constant (~0.5-1.0 for water)

**Typical performance:**

| Disk Diameter | Drive Power | Mist Rate | Application |
|---------------|-------------|-----------|-------------|
| 16 mm | 10-20 W | 25-35 g/h | Consumer diffuser |
| 20 mm | 20-40 W | 50-100 g/h | Mid-size humidifier |
| 25 mm | 40-100 W | 100-400 g/h | Industrial humidifier |
| 50 mm | 100+ W | 0.5-5 kg/h | Process atomization |

**C88 calculation:**
- 12 piezos × 20mm diameter
- 30W per piezo (typical)
- Total power: 360W
- Expected output: 12 × 75 g/h = **900 g/h** (0.9 L/h)

### 4.2 Efficiency

Atomization efficiency (η) = (energy in mist) / (electrical input)

**Typical values:**
- Consumer diffusers: 30-50%
- Industrial humidifiers: 50-70%
- Medical nebulizers: 70-85%
- **C88 target: >80%**

**Losses:**
- Heat generation in PZT (10-20%)
- Transformer losses (5-10%)
- MOSFET switching losses (5-10%)
- Acoustic radiation (5-10%)

---

## 5. Impedance Characteristics

### 5.1 Equivalent Circuit

Piezoelectric disk can be modeled as:

```
         ┌──[L_m]──[C_m]──[R_m]──┐
         │                        │
    ─────┤                        ├─────
         │                        │
         └────────[C_0]───────────┘
```

Where:
- L_m = motional inductance (mechanical mass)
- C_m = motional capacitance (mechanical compliance)
- R_m = motional resistance (mechanical losses)
- C_0 = static capacitance (electrode capacitance)

### 5.2 Resonance Frequencies

**Series resonance (f_s):**
```
f_s = 1 / (2π √(L_m × C_m))
```
- Minimum impedance
- Maximum current
- Used for atomization

**Parallel resonance (f_p):**
```
f_p = f_s × √(1 + C_m/C_0)
```
- Maximum impedance
- Used for sensing

**Typical values for 20mm, 1.7MHz PZT:**
- f_s = 1.70 MHz
- f_p = 1.75 MHz
- C_0 = 2-4 nF
- R_m = 5-20 Ω

### 5.3 Impedance Matching

Driver must match piezo impedance for maximum power transfer:

```
Z_driver = Z_piezo*
```

Where Z_piezo* is complex conjugate of piezo impedance.

**At resonance:**
- Piezo impedance is mostly resistive (R_m)
- Matching is simple: transformer turns ratio

**Off resonance:**
- Piezo impedance has reactive component
- Requires L-C matching network
- Efficiency drops dramatically

---

## 6. Temperature Effects

### 6.1 Frequency Drift

PZT resonance frequency changes with temperature:

```
Δf/f = k_T × ΔT
```

Where:
- k_T = temperature coefficient (-50 to +50 ppm/°C)
- ΔT = temperature change from 25°C

**Example:**
- k_T = -30 ppm/°C
- ΔT = +25°C (operating at 50°C)
- Δf = 1.7MHz × (-30×10⁻⁶) × 25 = **-1.275 kHz**

**C88 impact:** Frequency drift of ±1kHz is acceptable (1.7MHz ±0.1% spec).

### 6.2 Depolarization

PZT loses piezoelectric properties above Curie temperature:

| PZT Type | Curie Temp (°C) | Max Operating Temp (°C) |
|----------|-----------------|-------------------------|
| PZT-4 | 328 | 200 |
| PZT-5A | 365 | 220 |
| PZT-8 | 300 | 180 |

**C88 operating temp:** 10-50°C (well below Curie temp, no depolarization risk)

### 6.3 Thermal Runaway

At high drive power, PZT self-heating can cause:
1. Temperature rises
2. Mechanical losses increase
3. More heating
4. Thermal runaway → failure

**Prevention:**
- Adequate heat sinking
- Temperature monitoring (NTC thermistor)
- Power derating at high ambient temperature

---

## 7. Power and Drive Requirements

### 7.1 Why High Voltage?

To produce sufficient displacement amplitude (>1µm), the electric field must be high:

```
E = V / t

Where:
- E = electric field (V/m)
- V = applied voltage (V)
- t = piezo thickness (m)
```

**Example:**
- 1mm thick PZT
- Required field: 50,000 V/m
- Required voltage: 50V

**Typical drive voltage:** 50-120V peak-to-peak at piezo element

### 7.2 Why High Frequency?

Higher frequency produces:
- Smaller droplets (Lang equation)
- Faster response time
- Less acoustic noise (above human hearing)

**Trade-offs:**
- Higher frequency = smaller droplets but lower output
- 1.7MHz: good balance for C88 (2.3µm droplets, high output)
- 2.4MHz: smaller droplets (1.8µm) but 30% lower output

### 7.3 Drive Waveform

**Optimal:** Sinusoidal at resonance frequency

**Why not square wave?**
- Square wave contains harmonics (3f, 5f, 7f...)
- Harmonics cause unwanted vibration modes
- Reduced efficiency, more heat

**Practical:** Quasi-sinusoidal (some distortion acceptable)

---

## 8. Key Parameters Summary

### 8.1 For C88 Design

| Parameter | Value | Notes |
|-----------|-------|-------|
| Frequency | 1.7 MHz (primary) | 2.4 MHz alternative |
| Droplet size | 2.3 µm (1.7MHz) | Lang equation |
| Piezo diameter | 20 mm | Standard size |
| Piezo thickness | 1 mm | Typical |
| Drive voltage | 50-120 Vpp | At piezo element |
| Input voltage | 36-48V DC | For driver board |
| Power per piezo | 20-40 W | For 50-100 g/h |
| Total power (12 pcs) | 240-480 W | For 600-1200 g/h |
| Efficiency target | >80% | Including driver losses |

### 8.2 For Supplier Evaluation

**Questions to ask:**
1. What is the resonance frequency tolerance? (±0.05MHz typical)
2. What is the static capacitance C_0? (2-4 nF for 20mm)
3. What is the motional resistance R_m? (5-20 Ω)
4. What is the quality factor Q? (>500 for good piezo)
5. What is the Curie temperature? (>300°C for PZT-4/8)
6. What is the temperature coefficient k_T? (±50 ppm/°C max)

---

## 9. References

### 9.1 Foundational Papers

1. Lang, R.J. (1962). "Ultrasonic atomization of liquids". *Journal of the Acoustical Society of America*, 34(1), 6-8.  
   **Key contribution:** Derived droplet size-frequency relationship

2. Wood, R.W. & Loomis, A.L. (1927). "The physical and biological effects of high-frequency sound-waves of great intensity". *Philosophical Magazine*, 4(19), 417-436.  
   **Key contribution:** First observation of ultrasonic atomization

3. Sollner, K. (1945). "The production of aerosols by the condensation of supersaturated vapours". *Nature*, 155, 41-42.  
   **Key contribution:** Cavitation hypothesis

### 9.2 Technical References

4. "Ultrasonic atomization" — Wikipedia  
   URL: https://en.wikipedia.org/wiki/Ultrasonic_atomization  
   **Key content:** Comprehensive overview, Lang equation derivation

5. "Size distributions of droplets produced by ultrasonic nebulizers" — PMC  
   URL: https://pmc.ncbi.nlm.nih.gov/articles/PMC6468117  
   **Key content:** Experimental validation of Lang equation

6. "Understanding the Mechanism of Piezoelectric Atomizers" — Piezo Direct  
   URL: https://piezodirect.com/understanding-the-mechanism-of-piezoelectric-atomizers/  
   **Key content:** Practical explanation for engineers

### 9.3 Application Notes

7. "Troubleshooting Ultrasonic Atomizer MOSFET Driver Failures" — Industrial Monitor Direct  
   URL: https://industrialmonitordirect.com/blogs/knowledgebase/troubleshooting-ultrasonic-piezo-atomizer-driver-circuit-faults  
   **Key content:** Driver circuit design, failure modes

8. PZT Electronic (Dongguan) — Product specifications  
   URL: https://piezoelements.com  
   **Key content:** Real product specs, driver boards

---

## 10. C88 Application Notes

### 10.1 Why 1.7MHz?

**Droplet size:**
- 1.7MHz → 2.3µm (good for air suspension)
- 2.4MHz → 1.8µm (smaller but lower output)

**Output rate:**
- 1.7MHz → higher output (30% more than 2.4MHz)
- 2.4MHz → lower output but finer droplets

**Supplier availability:**
- 1.7MHz: widely available, proven technology
- 2.4MHz: less common, higher cost

**Recommendation:** Start with 1.7MHz for prototype, evaluate 2.4MHz if droplet size is issue.

### 10.2 Why 12 Piezos?

**Required output:**
- C88 target: 600-1200 g/h (0.6-1.2 L/h)
- Single 20mm piezo: 50-100 g/h
- Required: 6-12 piezos

**Redundancy:**
- 12 piezos allows 2-3 failures before system shutdown
- 6 piezos per module (2 modules) for independent control

**Uniformity:**
- 6 piezos in hexagonal pattern for even distribution
- Avoids hot spots and dry zones

### 10.3 Questions for Saturday SWT Visit

**Technical questions:**
1. What PZT material do you use? (PZT-4, PZT-5A, PZT-8?)
2. What is the d₃₃ coefficient? (should be >300 pC/N)
3. What is the quality factor Q? (should be >500)
4. What is the temperature coefficient? (should be <±50 ppm/°C)
5. How do you ensure frequency consistency across production?

**Performance questions:**
1. What is the atomization efficiency? (target >80%)
2. What is the mist output at 30W drive? (expect 50-100 g/h)
3. What is the frequency tolerance? (±0.05MHz typical)
4. How does output vary with temperature? (10-50°C range)

**Reliability questions:**
1. What is the accelerated aging test protocol?
2. How do you predict 10,000 hour lifetime?
3. What are the failure modes you've observed?
4. What is the warranty policy?

---

**End of Chapter 01 — Piezoelectric Atomization Physics**

**Next:** Chapter 02 — Anti-Corrosion Coating Technologies
