# Piezoelectric Atomizer Driver Circuit Design

**C88 Knowledge Base — Chapter 03**  
**Last Updated:** 2026-11-18  
**Purpose:** Technical reference for C88 piezo driver design and supplier evaluation

---

## 1. Why Piezo Needs 36-48V AC Drive Voltage

### 1.1 The Voltage-Amplitude Relationship

Piezoelectric ceramic disks convert electrical energy to mechanical vibration. The displacement amplitude (δ) is proportional to the applied electric field (E):

```
δ = d₃₃ × V × (t/t) = d₃₃ × V
```

Where:
- d₃₃ = piezoelectric coefficient (typically 200-650 pC/N for PZT)
- V = applied voltage
- t = piezo thickness

For a 20mm diameter, 1mm thick PZT disk to produce sufficient capillary wave amplitude (>1µm) for atomization, the required drive voltage is typically **50-120V peak-to-peak** at the piezo element.

### 1.2 Step-Up Transformer Architecture

Most commercial drivers use a **step-up transformer** to convert low-voltage DC (12-48V) to high-voltage AC:

```
DC Input (12-48V) → MOSFET Switch → Transformer Primary → Step-Up → Piezo (50-120Vpp)
```

**Why 35-48V input?**
- Lower voltage (12V) requires higher current for same power (P = V×I)
- Higher voltage reduces I²R losses in MOSFET and wiring
- 35V is common for 25mm atomizers; 48V for industrial units
- C88 spec: 36-48V DC allows flexibility in power supply selection

### 1.3 Real Product Example

**PZT Electronic PZT-25-1.7BU Board:**
- Input: 35V DC
- Frequency: 1.7 MHz
- Power: 35W
- Atomizer diameter: 25mm
- Water level: 25-30mm
- Includes: atomization board + power board + reed switch + indicator

---

## 2. Driver Circuit Topologies

### 2.1 Self-Oscillating Circuit (Colpitts/Pierce)

**Simplest approach:** Piezo element itself forms part of the oscillator feedback network.

```
         +Vcc
          |
         [L]  (choke)
          |
    +-----+-----+
    |           |
   [C1]       [C2]
    |           |
    +-----+-----+
          |
         [Piezo]
          |
         GND
```

**Advantages:**
- No external oscillator needed
- Automatically tracks piezo resonance
- Low component count
- Low cost (<$5 BOM)

**Disadvantages:**
- Frequency stability ±0.5-1%
- Hard to control power output
- Not suitable for multi-piezo arrays

**Use case:** Consumer humidifiers, aroma diffusers

### 2.2 Separate Oscillator + MOSFET Driver

**Modern approach:** Dedicated oscillator IC drives MOSFET gate.

```
Crystal Oscillator (1.7MHz) → Gate Driver IC → MOSFET → Transformer → Piezo
```

**Advantages:**
- Precise frequency control (±10 ppm with TCXO)
- PWM power control possible
- Can synchronize multiple drivers
- Better EMI performance

**Disadvantages:**
- Higher BOM cost ($10-20)
- More complex PCB layout
- Requires impedance matching network

**Use case:** Industrial atomizers, medical nebulizers, C88

### 2.3 Half-Bridge / Push-Pull Topology

**High-power approach:** Two MOSFETs alternate to drive transformer primary.

```
         +Vcc
          |
    +-----+-----+
    |           |
  [Q1]       [Q2]
    |           |
    +-----+-----+
          |
     [Transformer Primary]
          |
         GND
```

**Advantages:**
- Doubles power output vs single-ended
- Lower MOSFET stress (each sees Vcc, not 2×Vcc)
- Better efficiency (70-90%)
- Suitable for multi-piezo arrays

**Disadvantages:**
- Requires complementary gate drive (high-side + low-side)
- Risk of shoot-through if timing is wrong
- More complex control logic

**Use case:** C88 (12 piezos), industrial humidifiers

---

## 3. Frequency Control Methods

### 3.1 Crystal Oscillator (XO)

**Basic:** AT-cut quartz crystal, fixed frequency.

- Accuracy: ±20-50 ppm
- Stability: ±0.01%/°C
- Cost: $0.50-2.00
- **C88 suitability:** Good for fixed 1.7MHz design

### 3.2 Temperature-Compensated Crystal (TCXO)

**Enhanced:** Internal compensation for temperature drift.

- Accuracy: ±0.5-2.5 ppm
- Stability: ±0.001%/°C
- Cost: $2-10
- **C88 suitability:** Best for precision atomization

### 3.3 Phase-Locked Loop (PLL)

**Flexible:** Locks to reference frequency, can be tuned.

- Accuracy: ±0.1 ppm (locked)
- Tuning range: ±0.1-1%
- Cost: $3-8
- **C88 suitability:** Good for frequency sweep testing

### 3.4 Direct Digital Synthesis (DDS)

**Most flexible:** Digital generation, programmable frequency.

- Accuracy: <0.1 ppm
- Tuning range: Wide (DC to MHz)
- Cost: $5-15
- **C88 suitability:** Best for R&D, multi-frequency testing

**Recommendation for C88:** TCXO for production (cost-effective, stable), DDS for prototype (flexible).

---

## 4. Impedance Matching Network

### 4.1 Why Matching Matters

Piezo element impedance at resonance:
- Capacitive reactance: Xc = 1/(2πfC) ≈ 50-200Ω
- Resistive component: R ≈ 5-20Ω (motional resistance)

Without matching, most power reflects back to driver, causing:
- Low atomization efficiency
- MOSFET overheating
- Frequency instability

### 4.2 L-Network Matching

**Simplest:** Series inductor cancels capacitive reactance.

```
Driver → [L] → [Piezo] → GND
```

Where L is chosen so: 2πfL = 1/(2πfC)

**Example calculation:**
- Piezo capacitance: C = 2nF
- Frequency: f = 1.7MHz
- Required inductance: L = 1/((2π×1.7MHz)²×2nF) = 4.4µH

### 4.3 Transformer Matching

**Most common:** Step-up transformer provides both voltage boost and impedance transformation.

```
Driver (low-Z) → [Transformer] → Piezo (high-Z)
```

Turns ratio: n = √(Z_piezo / Z_driver)

**Example:**
- Driver output impedance: 5Ω
- Piezo impedance at resonance: 100Ω
- Turns ratio: n = √(100/5) = 4.5:1

### 4.4 Pi-Network (Advanced)

**Best performance:** L-C-L network for broadband matching.

```
Driver → [L1] → [C] → [L2] → Piezo
```

**Advantages:**
- Wider bandwidth
- Better harmonic suppression
- Can provide DC isolation

**Use case:** High-power industrial atomizers

---

## 5. Power Amplification Stages

### 5.1 MOSFET Selection Criteria

For 1.7MHz, 35W atomizer driver:

| Parameter | Minimum Spec | Recommended |
|-----------|--------------|-------------|
| V_DS (drain-source) | ≥60V | 100V |
| I_D (continuous drain) | ≥3A | 5A |
| R_DS(on) | <100mΩ | <50mΩ |
| Q_g (gate charge) | <20nC | <10nC |
| f_T (transition freq) | ≥50MHz | ≥100MHz |

**Recommended parts:**
- IRF510 (100V, 5A, R_DS=0.54Ω) — budget choice
- IRF740 (400V, 10A, R_DS=0.55Ω) — overkill but robust
- CSD17571Q5A (30V, 10A, R_DS=3.5mΩ) — low-voltage high-efficiency

### 5.2 Gate Drive Requirements

At 1.7MHz, gate drive is critical:

- Gate voltage: 10-15V (logic-level MOSFETs: 4.5V)
- Gate current: I_g = Q_g × f = 10nC × 1.7MHz = 17mA
- Rise time: <50ns (to minimize switching losses)
- Drive IC: TC4420 (high-speed, 6A peak)

### 5.3 Thermal Management

MOSFET power dissipation:

```
P_loss = I²_RMS × R_DS(on) + switching losses

Example:
- I_RMS = 2A
- R_DS(on) = 50mΩ
- Conduction loss = 2² × 0.05 = 0.2W
- Switching loss @ 1.7MHz ≈ 0.5W
- Total ≈ 0.7W
```

**Heatsink requirement:**
- Thermal resistance: θ_SA < (T_J_max - T_A) / P_loss
- For T_J_max = 150°C, T_A = 40°C, P_loss = 0.7W
- θ_SA < 157°C/W → small clip-on heatsink sufficient

---

## 6. Temperature Compensation

### 6.1 Piezo Frequency Drift

PZT resonance frequency shifts with temperature:

```
Δf/f = k_T × ΔT

Where:
- k_T = temperature coefficient ≈ -50 to +50 ppm/°C
- ΔT = temperature change from 25°C
```

**Example:**
- k_T = -30 ppm/°C
- ΔT = +25°C (operating at 50°C)
- Δf = 1.7MHz × (-30×10⁻⁶) × 25 = -1.275kHz

### 6.2 Compensation Methods

**Method 1: TCXO**
- Use temperature-compensated crystal oscillator
- Drift: ±0.5 ppm/°C
- Cost: $3-8

**Method 2: Frequency Tracking**
- Monitor piezo current phase
- Adjust oscillator to maintain resonance
- Requires PLL or DDS

**Method 3: NTC Thermistor**
- Measure piezo temperature
- Adjust oscillator frequency in software
- Requires MCU with lookup table

**C88 recommendation:** TCXO for simplicity (±0.5kHz drift acceptable for 1.7MHz ±1% spec).

---

## 7. Complete Module Design

### 7.1 Audiowell UM0108-003

**Specifications:**
- Frequency: 1.7 ±0.05 MHz
- Current: 0.65A
- Atomization rate: ≥360 mL/h
- Operating temp: +3°C to +50°C
- Input voltage: 24V DC (internal step-up)
- Control: Digital (UART/I2C)
- Dimensions: 45×45×25mm

**Features:**
- Integrated driver + piezo + housing
- Temperature sensor (NTC)
- Water level detection
- Over-current protection
- LED status indicator

**Price:** ~$25-40/unit (MOQ 100+)

### 7.2 KERI Integrated Module

**Specifications:**
- Frequency: 1.7 MHz or 2.4 MHz
- Power: 20-40W
- Anti-corrosion: HOCl/H₂O₂ compatible
- Lifetime: ≥8,000 hours
- Input voltage: 35V DC
- Control: PWM or analog

**Features:**
- Glass glaze coated piezo
- Stainless steel housing (316L)
- IP68 waterproof
- Dry-run protection

**Price:** ~$30-50/unit (MOQ 50+)

### 7.3 C88 Custom Module Design

**Requirements:**
- 6 piezos per module (2 modules = 12 total)
- 1.7 MHz or 2.4 MHz (TBD)
- HOCl/H₂O₂/PAA compatible
- Lifetime ≥10,000 hours
- 316L housing with Parylene coating

**Proposed architecture:**
```
48V DC Input → Half-Bridge Driver → 6× Transformer Secondaries → 6× Piezos
                ↓
           TCXO (1.7MHz) + MCU (STM32)
                ↓
        Current sensing + temp monitoring
```

**Estimated BOM:**
- Half-bridge driver: $8
- TCXO: $5
- MCU (STM32F103): $3
- 6× transformers: $12
- Current sensors: $6
- PCB + passives: $10
- **Total: ~$44** (vs $25-40 for Audiowell module)

**Trade-off:** Custom module is more expensive but gives full control and anti-corrosion design.

---

## 8. Design Trade-offs

### 8.1 Cost vs Performance

| Approach | Cost | Performance | Flexibility |
|----------|------|-------------|-------------|
| Buy Audiowell module | $25-40 | Good (proven) | Low (fixed) |
| Buy KERI module | $30-50 | Good (anti-corrosion) | Low (fixed) |
| Custom design | $44+ | Best (optimized) | High (customizable) |

### 8.2 Single Driver vs Multi-Channel

**Single driver (all 12 piezos in parallel):**
- Pros: Simple, low cost
- Cons: One failure kills all, hard to balance

**Multi-channel (6 drivers, 2 piezos each):**
- Pros: Redundancy, individual control
- Cons: Higher cost, complex PCB

**C88 recommendation:** 2 channels (6 piezos each), one per module.

### 8.3 Fixed Frequency vs Tunable

**Fixed (TCXO):**
- Pros: Simple, stable, low cost
- Cons: Can't optimize for piezo variation

**Tunable (DDS/PLL):**
- Pros: Can track piezo resonance, multi-frequency
- Cons: Complex, expensive, EMI issues

**C88 recommendation:** Fixed TCXO for production, DDS for R&D prototype.

---

## 9. Cost Considerations

### 9.1 Driver Board BOM Breakdown

**Low-cost design (single channel, 6 piezos):**

| Component | Qty | Unit Cost | Total |
|-----------|-----|-----------|-------|
| Half-bridge MOSFETs | 2 | $1.50 | $3.00 |
| Gate driver IC | 1 | $2.00 | $2.00 |
| TCXO 1.7MHz | 1 | $4.00 | $4.00 |
| Step-up transformer | 6 | $2.00 | $12.00 |
| Current sense resistors | 6 | $0.20 | $1.20 |
| MCU (STM32F103) | 1 | $3.00 | $3.00 |
| PCB (2-layer, 100×80mm) | 1 | $5.00 | $5.00 |
| Passives (caps, resistors) | 1 lot | $3.00 | $3.00 |
| Connectors | 1 lot | $2.00 | $2.00 |
| **Total** | | | **$35.20** |

### 9.2 Volume Pricing

At 100-unit volume:
- PCB: $3.50 (vs $5.00 prototype)
- Transformers: $1.50 ea (vs $2.00)
- **Total: ~$30/unit**

At 1000-unit volume:
- PCB: $2.00
- Transformers: $1.00 ea
- **Total: ~$25/unit**

### 9.3 Buy vs Build Analysis

| Option | Unit Cost | NRE | Lead Time | Risk |
|--------|-----------|-----|-----------|------|
| Audiowell module | $35 | $0 | 4 weeks | Low |
| KERI module | $40 | $0 | 6 weeks | Low |
| Custom design | $25 | $5,000 | 12 weeks | Medium |

**Break-even:** Custom design pays off at ~200 units (saves $10-15/unit vs modules).

**C88 recommendation:** Start with Audiowell/KERI modules for prototype (10-50 units), switch to custom design for production (100+ units).

---

## 10. References

### 10.1 Technical Papers

1. "Switching mode power convertor with phase locked oscillator as a driver for an ultrasonic atomizer" — IEEE, 2014  
   URL: https://ieeexplore.ieee.org/document/7070972

2. "Ultrasonic nebulizer for producing high-volume sub-micron droplets" — US Patent 7,129,619  
   URL: https://patents.google.com/patent/US7129619B2/en

3. "Ultrasonic Wave Nebulizer Driving Circuit" — US Patent 4,359,697  
   URL: https://patents.searchlight.law/doc/US4359697

### 10.2 Application Notes

4. "Troubleshooting Ultrasonic Atomizer MOSFET Driver Failures" — Industrial Monitor Direct  
   URL: https://industrialmonitordirect.com/blogs/knowledgebase/troubleshooting-ultrasonic-piezo-atomizer-driver-circuit-faults

5. "35V Atomizer Power Mainboard" — PZT Electronic (Dongguan)  
   URL: https://piezoelements.com/pcb-driver-board/35v-atomizer-power-mainboard.html

### 10.3 Supplier Documents

6. Audiowell UM0108-003 Smart Atomizer Module Datasheet  
   URL: https://audiowell.com/transducer.html

7. KERI Anti-Corrosion Atomizer Module Specifications  
   URL: https://www.keri.com.cn (requires login)

### 10.4 Design Tools

8. "2.4mhz Piezo atomizer circuit" — Vancouver Hack Space forum discussion  
   URL: https://talk.vanhack.ca/t/2-4mhz-piezo-atomizer-circuit/7420

---

## 11. C88 Application Notes

### 11.1 Key Design Decisions

**Frequency:** 1.7MHz (primary) or 2.4MHz (alternative)
- 1.7MHz: Larger droplets (2.3µm), higher output, proven technology
- 2.4MHz: Smaller droplets (1.5µm), lower output, better penetration

**Voltage:** 36-48V DC
- 36V: Lower stress on components, suitable for prototype
- 48V: Higher power, better for production (12 piezos)

**Module configuration:** 2 modules × 6 piezos
- Independent channels for redundancy
- Each channel: 35W driver, 6 transformers

### 11.2 Questions for Supplier Discussions

**For Audiowell:**
1. Can UM0108 module be customized for HOCl environment?
2. What is the input voltage range (24V or 48V)?
3. Can modules be synchronized (phase-locked)?
4. What is the MTBF (mean time between failures)?

**For KERI:**
1. Glass glaze coating thickness and composition?
2. Accelerated aging test data for HOCl 2000ppm?
3. Can driver board be separated from piezo housing?
4. What is the frequency tolerance (±0.05MHz or tighter)?

**For J&H (吉胜辉):**
1. Glass glaze anti-corrosion mechanism?
2. Test data for H₂O₂ 7.5% and PAA 10,000ppm?
3. Can you provide complete module (piezo + driver)?
4. What is the minimum order quantity for custom design?

### 11.3 Prototype Testing Plan

**Phase 1: Single piezo validation (Week 1-2)**
- Test 1× piezo with commercial driver board
- Measure atomization rate, droplet size, power consumption
- Validate frequency and voltage requirements

**Phase 2: 6-piezo module (Week 3-4)**
- Build custom driver board for 6 piezos
- Test uniformity (all 6 piezos same output?)
- Measure thermal performance (MOSFET temperature)

**Phase 3: Full system (Week 5-6)**
- Integrate 2 modules (12 piezos total)
- Test in 316L tank with HOCl solution
- Measure lifetime (accelerated aging)

---

**End of Chapter 03 — Driver Circuit Design**

**Next:** Chapter 04 — Lifetime Testing Methods (in progress)
