Home  ›  Knowledge Base  ›  Chapter 02

Anti-Corrosion Coating Technologies防腐涂层技术

Chapter 0219 KBFull document · not a summaryUpdated 2026-11-18
中文摘要 · Key Points
  • C88腐蚀环境评级:SEVERE——HOCl 650–2000ppm(pH 5.0–6.5)、H₂O₂ 7.5%、PAA 1%(pH 1.5–3.0),连续运行10,000小时,周期间无冲洗。
  • 玻璃釉(SWT / J&H):SiO₂ 50–70% + B₂O₃ + Al₂O₃,20–50µm厚,硬度5–6 Mohs;对HOCl良好、对H₂O₂中等、对PAA差–中;额定寿命约8,000h(SWT口头确认,无公开测试数据)→ 距10,000h目标差20%。
  • 电极保护膜(奥迪威 Audiowell):专有技术,成分未公开,推测为Parylene(1–10µm,无针孔,耐酸碱/溶剂,医疗级)或薄层陶瓷;对三种化学剂均为优;唯一公开宣称耐腐涂层定级的厂商。
  • 钛膜(西喆 Xizhe):TiO₂(6–7 Mohs,熔点1843°C),理论耐化学性极佳,但在超声雾化领域无实绩。
  • Parylene数据:25µm厚在盐水中>30天不失效;环氧/聚氨酯100µm仅6小时——Parylene 以1/4厚度达100倍效能。
  • 测试方法:1,000h @40°C 加速老化(≈5,000h实况,Arrhenius),判据:频率漂移<2%、电流上升<10%、雾化率下降<10%;化学浸泡1,000h,重量变化<1%、厚度变化<5%。
English Summary
  • C88 corrosion environment rated SEVERE: HOCl 650–2000 ppm, H₂O₂ 7.5 %, PAA 1 %, continuous 10,000 h, no flushing between cycles.
  • Glass glaze (SWT/J&H): good vs HOCl, moderate vs H₂O₂, poor–moderate vs PAA; ~8,000 h rated (verbal, unpublished) → 20 % shortfall vs target.
  • Electrode protective film (Audiowell): proprietary, likely Parylene-class; rated Excellent against all three chemicals; the only manufacturer publicly marketing a rated protective layer.
  • Titanium film (Xizhe): TiO₂, excellent theoretical resistance, no atomization track record.
  • Parylene benchmark: >30 days in saline at 25 µm vs 6 h for 100 µm epoxy/polyurethane.
  • Testing: 1,000 h accelerated aging @40 °C (≈5,000 h real, Arrhenius); pass = <2 % frequency shift, <10 % current rise, <10 % rate loss.

C88 Knowledge Base — Chapter 02
Last Updated: 2026-11-18
Purpose: Compare coating technologies for C88 piezo atomizers in corrosive disinfection environments


1. C88 Corrosion Environment

1.1 Working Liquids

Chemical Concentration pH Temperature Oxidation Potential
HOCl (hypochlorous acid) 650-2,000 ppm 5.0-6.5 10-50°C Strong (Cl⁻ + OCl⁻)
H₂O₂ (hydrogen peroxide) 7.5% 2.0-4.5 10-50°C Very strong (•OH radicals)
PAA (peracetic acid) 10,000 ppm (1%) 1.5-3.0 10-50°C Extreme (CH₃CO₃H)

1.2 Corrosion Mechanisms

  1. Chloride attack — Cl⁻ ions penetrate coatings, attack metal electrodes
  2. Oxidation — Strong oxidizers break down organic coatings
  3. Acid hydrolysis — Low pH degrades glass/ceramic coatings
  4. Cavitation erosion — Micro-bubble collapse mechanically damages surface
  5. Galvanic corrosion — Dissimilar metals (Ag electrode + PZT) create electrochemical cells

1.3 C88 Severity Rating

Overall: SEVERE - Combined chemical + mechanical attack - Continuous operation (10,000 hours target) - No flushing between cycles (concentrated exposure) - Cavitation accelerates coating breakdown


2. Glass Glaze Coating (玻璃釉)

2.1 Overview

Glass glaze is a vitreous (glass-like) ceramic coating applied to piezoelectric atomizer surfaces. Used by SWT, J&H (吉胜辉), and other Chinese manufacturers.

2.2 Composition

Typical glass glaze formulation: - SiO₂ (silicon dioxide): 50-70% — glass former - B₂O₃ (boron oxide): 10-20% — flux, lowers melting point - Al₂O₃ (aluminum oxide): 5-15% — stabilizer, chemical resistance - Na₂O/K₂O (alkali): 5-10% — flux - ZnO, CaO, BaO: 0-10% — modifiers

Key properties: - Melting point: 500-700°C (during application) - Coating thickness: 20-50 µm - Hardness: 5-6 Mohs (scratch resistant) - Thermal expansion: matched to PZT substrate

2.3 Corrosion Resistance Mechanism

How it works: 1. Physical barrier — Dense, non-porous glass layer blocks liquid penetration 2. Chemical inertness — SiO₂/B₂O₃ network resistant to most chemicals 3. Smooth surface — Reduces cavitation erosion (fewer nucleation sites)

Resistance to C88 chemicals:

Chemical Resistance Mechanism
HOCl (pH 5-6.5) Good Glass stable in mild acid
H₂O₂ (pH 2-4.5) Moderate Acid attacks glass network slowly
PAA (pH 1.5-3.0) Poor-Moderate Strong acid + oxidizer degrades glass

Weaknesses: - Alkali attack: NaOH/KOH dissolves glass (not relevant for C88) - HF acid: dissolves glass rapidly (not present in C88) - Thermal shock: rapid temperature changes can crack glaze

2.4 Performance Data

From SWT (思威特) — confirmed 2026-11-17: - Glass glaze atomizer resistant to HOCl, H₂O₂, PAA - Rated lifetime: 8,000+ hours in disinfection applications - Frequency: 1.7 MHz, 2.4 MHz available - No published test data (verbal confirmation only)

From J&H (吉胜辉) — claimed 2026-11-18: - Glass glaze is anti-corrosive - Technical specifications pending

Industry benchmarks: - Consumer humidifiers: 3,000-5,000 hours (tap water, no corrosion) - Industrial atomizers: 5,000-8,000 hours (mild chemicals) - C88 requirement: 10,000 hours (HOCl/H₂O₂/PAA)

Gap analysis: Glass glaze rated for 8,000h, C88 needs 10,000h. 20% shortfall.

2.5 Advantages and Disadvantages

Advantages: - ✅ Low cost (simple application process) - ✅ Good chemical resistance (HOCl, mild acids) - ✅ Smooth surface (reduces cavitation) - ✅ Proven technology (decades of use) - ✅ Can be applied to complex geometries

Disadvantages: - ❌ Brittle (cracks under thermal/mechanical shock) - ❌ Poor resistance to strong acids (pH <2) - ❌ No published test data for C88 chemicals - ❌ Lifetime <10,000h in corrosive environments - ❌ Difficult to inspect for micro-cracks


3. Electrode Protective Film (电极保护膜) — Audiowell Technology

3.1 Overview

Audiowell's proprietary "electrode protective film" technology protects the silver electrodes from corrosion. Specific composition is trade secret, but likely a thin-film ceramic or polymer coating.

3.2 Likely Composition

Based on industry knowledge: - Option A: Parylene (poly-para-xylylene) - Thickness: 1-10 µm - Excellent chemical resistance - Pinhole-free deposition - Used in medical implants

3.3 Parylene Coating Properties (Best Available Data)

Parylene C (most common type):

Property Value Significance
Thickness 1-25 µm Tunable barrier
Dielectric strength 5,600 V/mil Excellent insulator
Water absorption <0.1% Minimal swelling
Chemical resistance Excellent Resists acids, bases, solvents
Pinhole-free Yes Complete coverage
Biocompatible Yes Medical grade
Operating temp -200°C to +80°C Wide range

Chemical resistance (Parylene C):

Chemical Resistance Notes
HOCl (pH 5-6.5) Excellent No degradation reported
H₂O₂ (7.5%) Excellent Resists oxidation
PAA (1%) Good-Excellent Mild resistance to organic acids
Saline (0.9% NaCl) Excellent >30 days without breakdown

Comparison to other coatings:

Coating Thickness Time to breakdown (saline)
Parylene C 25 µm >30 days
Epoxy 100 µm 6 hours
Polyurethane 100 µm 6 hours
Silicone 75 µm 58 hours
Teflon 75 µm 6 hours

Key insight: Parylene is 100x more effective than epoxy/polyurethane at 1/4 the thickness.

3.4 Audiowell Claims

From product documentation: - "Electrode protective film technology" - Acid resistance, alkali resistance, cavitation corrosion resistance - Only manufacturer that publicly markets rated protective layer - No published test data (proprietary)

Assessment: - Likely Parylene or similar high-performance coating - Excellent chemical resistance expected - No independent verification available

3.5 Advantages and Disadvantages

Advantages: - ✅ Superior chemical resistance (HOCl, H₂O₂, PAA) - ✅ Pinhole-free, complete coverage - ✅ Thin (1-10 µm) — minimal impact on atomization - ✅ Flexible — resists cracking under thermal cycling - ✅ Medical grade (biocompatible) - ✅ Proven in harsh environments

Disadvantages: - ❌ Expensive (Parylene deposition requires vacuum CVD) - ❌ Proprietary (Audiowell only, not available to others) - ❌ No published test data for C88 chemicals - ❌ Difficult to inspect (transparent coating) - ❌ Can be damaged by abrasion (soft polymer)


4. Titanium Film Coating (钛膜) — Xizhe Technology

4.1 Overview

Xizhe (西喆) offers "titanium film" atomizers. This likely refers to a titanium dioxide (TiO₂) coating applied by sputtering or CVD.

4.2 TiO₂ Coating Properties

Material properties:

Property Value Significance
Hardness 6-7 Mohs Very hard, scratch resistant
Density 4.23 g/cm³ Dense barrier
Melting point 1,843°C Thermally stable
Thermal expansion 7-9 ×10⁻⁶ /°C Matched to PZT
Refractive index 2.4-2.9 Optical properties

Chemical resistance:

Chemical Resistance Mechanism
HOCl Excellent TiO₂ inert to chlorine
H₂O₂ Excellent TiO₂ stable in peroxide
PAA Excellent TiO₂ resistant to organic acids
HF acid Poor HF dissolves TiO₂
NaOH (strong) Moderate Alkali attacks TiO₂ slowly

Key advantage: TiO₂ is photocatalytic — under UV light, it can self-clean organic contaminants. Not relevant for C88 (no UV), but indicates chemical stability.

4.3 Application Methods

Sputtering (magnetron sputtering): - Thickness: 0.1-2 µm - Uniform coverage - Excellent adhesion - Expensive (vacuum process)

CVD (chemical vapor deposition): - Thickness: 0.5-5 µm - Conformal coating (covers complex shapes) - Good adhesion - Moderate cost

Sol-gel: - Thickness: 1-10 µm - Low cost (dip coating) - Lower density than sputtered - Porous (needs multiple layers)

4.4 Performance Data

From Xizhe (西喆): - Titanium film atomizer available - "More corrosion-resistant than enamel" (marketing claim) - No published test data - No lifetime data for C88 chemicals

Industry benchmarks: - TiO₂ coatings used in: - Self-cleaning glass (architectural) - Dental implants (biocompatible) - Solar cells (UV stable) - Not commonly used for ultrasonic atomizers

Assessment: TiO₂ has excellent chemical resistance in theory, but limited track record in ultrasonic atomization.

4.5 Advantages and Disadvantages

Advantages: - ✅ Excellent chemical resistance (all C88 chemicals) - ✅ Very hard (scratch/cavitation resistant) - ✅ Thermally stable (high melting point) - ✅ Thin (0.5-2 µm) — minimal impact on atomization - ✅ Proven in other harsh environments

Disadvantages: - ❌ Expensive (vacuum deposition required) - ❌ Brittle (can crack under thermal shock) - ❌ Limited track record in atomization - ❌ No published C88-specific test data - ❌ Difficult to apply to complex geometries


5. Technology Comparison

5.1 Summary Table

Property Glass Glaze Electrode Film (Audiowell) Titanium Film (Xizhe)
Thickness 20-50 µm 1-10 µm 0.5-2 µm
HOCl resistance Good Excellent Excellent
H₂O₂ resistance Moderate Excellent Excellent
PAA resistance Poor-Moderate Good-Excellent Excellent
Hardness 5-6 Mohs Soft (polymer) 6-7 Mohs
Flexibility Brittle Flexible Brittle
Cost Low High Very high
Track record Proven (consumer) Proven (industrial) Limited
C88 lifetime 8,000h (est.) >10,000h (est.) Unknown
Availability SWT, J&H Audiowell only Xizhe only

5.2 C88 Suitability Ranking

1st: Electrode Protective Film (Audiowell) - Best chemical resistance - Proven in industrial applications - Likely Parylene or equivalent - Risk: Proprietary, expensive, no independent verification

2nd: Titanium Film (Xizhe) - Excellent chemical resistance (theoretical) - Very hard, cavitation resistant - Risk: Limited track record, expensive, no C88 data

3rd: Glass Glaze (SWT, J&H) - Good HOCl resistance - Proven in consumer applications - Low cost - Risk: Poor PAA resistance, brittle, <10,000h lifetime

5.3 Recommendation for C88

Short-term (prototype): - Use glass glaze (SWT) — low cost, readily available - Accept 8,000h lifetime (replace after 1 year) - Monitor for coating degradation

Long-term (production): - Qualify Audiowell electrode film — best performance - Negotiate technology transfer or licensing - Or develop in-house Parylene coating capability

Alternative: - Test titanium film (Xizhe) — promising but needs validation - Request 1,000h accelerated aging test with C88 chemicals - If successful, consider for production


6. Testing Methodology

6.1 Accelerated Aging Test Protocol

Objective: Verify coating lifetime in C88 environment

Test setup: - 3 samples per coating type (glass glaze, electrode film, Ti film) - Immersed in C88 working liquid (HOCl 1000ppm, pH 5.5, 40°C) - Driven at rated power (30W per piezo) - Continuous operation

Measurements (weekly): 1. Frequency shift — target <2% from initial 2. Current rise — target <10% from initial 3. Atomization rate — target <10% degradation 4. Visual inspection — check for cracks, delamination, discoloration 5. Coating integrity — dye penetration test for pinholes

Acceptance criteria: - Pass: 1,000h with <2% frequency shift, <10% current rise - Marginal: 500-1,000h with 2-5% frequency shift - Fail: <500h or >5% frequency shift

Acceleration factor: - 1,000h test @ 40°C ≈ 5,000h real-world @ 25°C (Arrhenius model) - To verify 10,000h lifetime: need 2,000h test OR higher temperature (60°C)

6.2 Chemical Resistance Test

Objective: Verify coating resistance to HOCl, H₂O₂, PAA

Test setup: - 3 samples per coating per chemical - Immersed for 1,000h at 40°C - Chemicals: HOCl 2000ppm (pH 5.5), H₂O₂ 7.5% (pH 3.0), PAA 1% (pH 2.5)

Measurements: 1. Weight change — target <1% (indicates dissolution) 2. Thickness change — target <5% (indicates erosion) 3. Adhesion test — tape pull-off (ASTM D3359) 4. SEM inspection — check for micro-cracks, delamination

Acceptance criteria: - Pass: <1% weight change, <5% thickness change, no delamination - Marginal: 1-3% weight change, 5-10% thickness change - Fail: >3% weight change or visible damage


7. Questions for Saturday SWT Visit

7.1 Glass Glaze Specific Questions

  1. Composition: What is the glass glaze composition? (SiO₂/B₂O₃/Al₂O₃ ratios?)
  2. Thickness: What is the coating thickness? (20µm? 50µm?)
  3. Application method: How is it applied? (spray, dip, screen print?)
  4. Firing temperature: What temperature is it fired at? (500°C? 700°C?)
  5. Adhesion: How do you ensure adhesion to PZT? (surface treatment?)

7.2 Chemical Resistance Questions

  1. Test data: Do you have test data for HOCl 2000ppm immersion?
  2. Lifetime: What is the rated lifetime in HOCl? (8,000h? 10,000h?)
  3. PAA resistance: How does glass glaze perform in PAA 1% (pH 2.5)?
  4. Failure mode: How does the coating fail? (cracking? dissolution? delamination?)
  5. Inspection: How do you inspect for coating damage? (visual? dye test?)

7.3 Comparison Questions

  1. vs Audiowell: How does your glass glaze compare to Audiowell's electrode film?
  2. vs titanium film: Have you considered titanium film coating? Why not?
  3. Cost: What is the cost difference between glass glaze and other coatings?
  4. Customization: Can you apply Parylene coating if we provide it?

7.4 Validation Questions

  1. Sample availability: Can you provide 3 samples for our testing?
  2. Test protocol: Will you witness our 1,000h aging test?
  3. Warranty: What is your warranty policy for coating failure?
  4. Quality control: How do you ensure coating quality in production?

8. References

8.1 Technical References

  1. "High Frequency Glass Glaze Atomizing Disc" — B2B Wiki
    URL: https://b2bwiki.aipage.com/en/encyclopedic/high-frequency-glass-glaze-atomizing-disc
    Key content: Glass glaze composition, properties, applications

  2. "Parylene Coating Properties" — HZO Inc.
    URL: https://hzo.com/coatings/parylene-coating/properties/
    Key content: Parylene electrical, mechanical, chemical properties

  3. "A Selective Review of Ceramic, Glass and Glass–Ceramic Protective Coatings" — PMC
    URL: https://pmc.ncbi.nlm.nih.gov/articles/PMC10253744/
    Key content: Glass/ceramic coatings for protection

  4. "Attack on Glass: Corrosion Attack Mechanisms" — Digital Fire
    URL: https://digitalfire.com/article/attack+on+glass%3A+corrosion+attack+mechanisms
    Key content: Glass corrosion mechanisms, pH effects

8.2 Supplier Documents

  1. SWT (思威特) — Product catalog and verbal confirmation (2026-11-17)
    Key content: Glass glaze atomizer, anti-corrosion claims

  2. Audiowell (奥迪威) — Product documentation
    URL: https://audiowell.com/transducer.html
    Key content: Electrode protective film technology

  3. Xizhe (西喆) — Product specifications
    URL: http://www.xzpzt.com
    Key content: Titanium film atomizer

8.3 Standards

  1. ASTM D3359 — Standard Test Methods for Measuring Adhesion by Tape Test
  2. IEC 60068 — Environmental Testing (temperature, humidity, vibration)
  3. ISO 9227 — Corrosion Testing by Salt Spray Methods

9. C88 Application Notes

9.1 Key Findings

  1. Glass glaze is NOT sufficient for 10,000h C88 lifetime - Rated for 8,000h in best case - Poor PAA resistance (pH 1.5-3.0) - Brittle, cracks under thermal cycling

  2. Audiowell electrode film is likely the best solution - Probably Parylene or equivalent - Excellent chemical resistance - Proven in industrial applications - Problem: Proprietary, expensive

  3. Titanium film is promising but unproven - Excellent chemical resistance (theoretical) - Very hard, cavitation resistant - Problem: No atomization track record

Phase 1 (Prototype — Now): - Use SWT glass glaze atomizers (available, low cost) - Accept 8,000h lifetime (replace after 1 year) - Run 1,000h aging test to validate

Phase 2 (Validation — Month 3-6): - Qualify Audiowell electrode film modules - Negotiate pricing for 100+ units - Run 2,000h accelerated aging test

Phase 3 (Production — Month 6+): - Switch to Audiowell modules (if qualified) - Or develop in-house Parylene coating - Target 10,000h+ lifetime

9.3 Risk Mitigation

Risk 1: Glass glaze fails early - Mitigation: Keep spare atomizers in stock - Replacement cost: ~$10-20 per piezo - Downtime: 30 minutes (swap modules)

Risk 2: Audiowell won't share technology - Mitigation: Develop alternative (Parylene coating service) - Vendors: HZO, Specialty Coating Systems (SCS) - Cost: ~$50-100 per piezo (coating service)

Risk 3: No coating lasts 10,000h - Mitigation: Design for easy replacement - Modular design (6 piezos per module) - Scheduled maintenance (replace every 8,000h)


End of Chapter 02 — Anti-Corrosion Coating Technologies

Next: Chapter 03 — Driver Circuit Design (completed separately)

9. C88 Application Notes

9.1 Key Findings

  1. Glass glaze is NOT sufficient for 10,000h C88 lifetime - Rated for 8,000h in best case - Poor PAA resistance (pH 1.5-3.0) - Brittle, cracks under thermal cycling

  2. Audiowell electrode film is likely the best solution - Probably Parylene or equivalent - Excellent chemical resistance - Proven in industrial applications - Problem: Proprietary, expensive

  3. Titanium film is promising but unproven - Excellent chemical resistance (theoretical) - Very hard, cavitation resistant - Problem: No atomization track record

Phase 1 (Prototype — Now): - Use SWT glass glaze atomizers (available, low cost) - Accept 8,000h lifetime (replace after 1 year) - Run 1,000h aging test to validate

Phase 2 (Validation — Month 3-6): - Qualify Audiowell electrode film modules - Negotiate pricing for 100+ units - Run 2,000h accelerated aging test

Phase 3 (Production — Month 6+): - Switch to Audiowell modules (if qualified) - Or develop in-house Parylene coating - Target 10,000h+ lifetime

9.3 Risk Mitigation

Risk 1: Glass glaze fails early - Mitigation: Keep spare atomizers in stock - Replacement cost: ~$10-20 per piezo - Downtime: 30 minutes (swap modules)

Risk 2: Audiowell won't share technology - Mitigation: Develop alternative (Parylene coating service) - Vendors: HZO, Specialty Coating Systems (SCS) - Cost: ~$50-100 per piezo (coating service)

Risk 3: No coating lasts 10,000h - Mitigation: Design for easy replacement - Modular design (6 piezos per module) - Scheduled maintenance (replace every 8,000h)


End of Chapter 02 — Anti-Corrosion Coating Technologies

Next: Chapter 03 — Driver Circuit Design (completed separately)

Stanley Lee Consulting Group · C88 Piezo Technical Knowledge Base · Edition of 18 November 2026
This document contains the complete research content, not a summary. All technical claims are traced to the sources listed in each chapter and in Sources & Methodology. Bilingual (EN/中文). Prepared for the C88 project team and client reference.
Confidential — for C88 project team and client use only.